How To Remove A Cast Iron Alcove Tub ~ Looks Like Easy

Cover the cast iron tub with a piece of plywood. Heavy cast iron tubs or bathtubs with tiling surrounds can cost $1,000 or more to remove.

KOHLER Bellwether 60 in. x 30 in. ADA Cast Iron Alcove

Cast iron tubs can weigh over 300lbs easily depending on the size, shape, and wall thickness, which makes them very difficult to remove.

How to remove a cast iron alcove tub. You can start the process by using a 2lb sledgehammer on the apron. I picked up a kohler villager cast iron tub yesterday, which is currently in my garage. In some cases, structural reinforcement of floors may be necessary if you want to install a large cast iron bathtub.

Then, remove the drain from the bottom of the tub, saw the drain pipe off, and remove it too. This is important because you don't want any debris to fall into the tub and crack it as you proceed further into this process. Remove any stringer supports left on the wall.

American standard alcove bathtub best bathtubs alcove tub bathtub. Unhooking the drain is similar to a sink drain: Typically, the tub is installed in an alcove section of the bathroom with three of its sides enclosed by a wall.

An alcove bathtub is a tub that is surrounded by three walls.you may find that when it comes to removing this type of tub, it can be a more difficult task than a standalone type of bathtub. Cut away a horizontal strip of wall about 6 inches above the bathtub to reveal the tub flange, and remove any screws that secure the flange to the wall studs. The restoration of the cast iron tub begins.

So the only way to remove a cast iron tub is in pieces. Slide the tub out of the alcove using the 1 x 4 boards as skids. Unpack the tub, set it upright on the 2x4 boards and slide it all the way into the alcove to make sure it fits.

One person should lift the front edge of the tub, while another slides a couple of 1 x 4 boards underneath to get it off the floor. It can be cut with angle grinder with metal blade (that method will require dust mask. A cast iron alcove bathtub like a kohler villager weighs approximately 316lbs making it darned near impossible for one person to remove or to install for that matter.

If you cut the tub in half, just leave the overflow attached. He cleaned the bathtub to remove the grime. If there are any gaps between the tub flange and the studs, this is the last chance to make corrections to the wall framing.

Test that the bathtub is level with a spirit level and shim it with metal shims if necessary. Using a putty knife, the technician carved away the caulk caught between the walls and the tub. Removing your cast iron tub might seem like a daunting task, but if you break it down into smaller steps, it should be relatively straightforward.

The largest clawfoot tubs can weigh well over 500 pounds when dry and more than 1,000 pounds when filled with water. The term alcove doesn't refer to the shape or size of the bathtub, but the installation. You may need to cut the plywood to make sure it fits snugly above the bathtub.

The low prices for alcove bathtubs sit in the 400 to 500 range. Hopefully the post content article how to remove an alcove bathtub, what we write can you understand. I've tried both methods in the past so i can help you prepare for what you're in store for.

First, turn off the water at the shutoff valve. Next, he removed the drain cover and covered the faucets. Remove the front, side, and rear walls of the tub.

You can use a reciprocating. I contact metal scrappers who will haul it out for free. Be safe and have a helper for these next few steps.

Even in half, cast iron is heavy. A kohler 5ft x 18 was close to 400 pounds. Acrylic is stronger than fiberglass but.

When everything checks out, slide the tub all the way out of the alcove. However, with the right tools and the correct amount of know how, you will find that this is a task that is not too difficult. On the front side, you can place a shower curtain or bathtub door to provide privacy.

Alcove bathtub enamel cast iron. Depending on what your plans are for the tub, you have several different methods you can use to remove one. Today i searched forums on how to remove a cast iron tub after all answers suggested a sledgehammer, i tried a 4 1/2 inch grinder with a metal cutting blade.to me it proved easier than the sledge idea.its a small bath soon to be 3 foot deeper.

The steps taken to give the cast iron tub a new beginning are as follows:

Kohler K7160 White Villager Collection 60" Cast Iron